If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
cutting circles out of glass - tips ?
Hi All
Fresh from my success with the big (to me!) stained glass window ... - the new project requires me to cut a hole out of a piece of 'art' glass. The hole needs to be circular - and in the region of 1" to 2.5" diameter... I have the Morton hole-cutter attachment - and have become reasonably good at cutting circular pieces of glass with it - but in this case i want to end up with the 'negative' of this . I can make the circular score - no problem. It's geting the piece of scrap glass out of the middle of the hole without losing/cracking the main piece that's causing me problems. Anybody prepared to share their special tips, please ? (And, no, I don't expect it to be as easy as in the movies! g) Thanks in advance Adrian Suffolk UK |
Ads |
#2
|
|||
|
|||
Your safest bet is to core drill the hole. Do not try to scratch it.
Randy Hansen SC Glass Tech. Scam Diego, Comi-fornia |
#3
|
|||
|
|||
i did this. i took a 3" hole out of the interior of a 16" disk.
draw out the interior hole with a sharpie. use a minibit on your grinder to drill a sequence of holes around the perimeter of this line, and a few on the interior of the circle in a small area. score around the perimeter. make lots of scores between the perimeter holes and the interior holes, and across the diameters in a lot of places. CAREFULLY break out the small areas between the interior holes with grozers. work on grozing out the rest of the interior pieces. use the large grinder head to smooth out the perimeter. if you do it wrong, you just start over. ps: i heard of someone just scoring the interior cut, and then just punching out the hole with a fist. "Adrian Brentnall" wrote in message ... Hi All Fresh from my success with the big (to me!) stained glass window ... - the new project requires me to cut a hole out of a piece of 'art' glass. The hole needs to be circular - and in the region of 1" to 2.5" diameter... I have the Morton hole-cutter attachment - and have become reasonably good at cutting circular pieces of glass with it - but in this case i want to end up with the 'negative' of this . I can make the circular score - no problem. It's geting the piece of scrap glass out of the middle of the hole without losing/cracking the main piece that's causing me problems. Anybody prepared to share their special tips, please ? (And, no, I don't expect it to be as easy as in the movies! g) Thanks in advance Adrian Suffolk UK |
#4
|
|||
|
|||
even after repeated attempts and should you be successful, the doughnut
(hole) will always be at risk for cracking. Add heat from a soldering iron and for sure a recipe for a crack. Watch how they "cut a hole" on TV or the movies ....they usually show a sliding door, and we all know that is safety glass, cannot cut a hole in it. \if they could tap on the inside (other side) of the glass why would they have to cut a hole to gain entry...... MUST BE TRUE MARTHA, I saw it on TV!!!!!!!!!!! BUT, I too have succumbed to the hole cutting in glass fro an "unusual" effect..... h -- In the words of the IMMORTAL USED CAR DEALER: THERE IS AN ASS FOR EVERY SEAT! |
#5
|
|||
|
|||
Although it's easier to just drill the hole out, you can cut a circle
out from inside a piece of glass. Here's a method I use as a demo in my Cutting Clinics. It's very effective at demonstrating "impossible" cuts. 1. Score the circle you want. Unless you're EXTREMELY good cutting by hand, I'd suggest using a circle cutter. 2. Turn the glass over, lay it flat on your table, and tap the circular score until it has cracked completely along the score. 3. Turn the glass back to the original side and score an "X" and a "+" to divide the circle into 8 pie-shaped pieces. (BE CAREFUL to NOT run the score past the original score for the circle. Stop those scores about 1/8" short of the circle score. 4. Turn the glass over, again lay it flat on the table, and tap those scores until they have all completely cracked. 5. Stand the glass up vertical and tap the center where the scores intersect. The pie-shaped pieces will fall out leaving a hole in the glass. You can also use this same method to cut out extremely complex shapes other than circles. |
#6
|
|||
|
|||
"Adrian Brentnall" wrote in message ... Hi All Fresh from my success with the big (to me!) stained glass window ... - the new project requires me to cut a hole out of a piece of 'art' glass. The hole needs to be circular - and in the region of 1" to 2.5" diameter... I have the Morton hole-cutter attachment - and have become reasonably good at cutting circular pieces of glass with it - but in this case i want to end up with the 'negative' of this . I can make the circular score - no problem. It's geting the piece of scrap glass out of the middle of the hole without losing/cracking the main piece that's causing me problems. Anybody prepared to share their special tips, please ? (And, no, I don't expect it to be as easy as in the movies! g) Thanks in advance Adrian Suffolk UK As I tell my beginner students.... all those cat burglar movies where the guy scores a circle and suction cups it cleanly out are BS.... you need to be on the inside of the window to tap it! -- JK Sinrod Sinrod Stained Glass Studios www.sinrodstudios.com Coney Island Memories www.sinrodstudios.com/coneymemories |
#7
|
|||
|
|||
Hi Randy
Your safest bet is to core drill the hole. Do not try to scratch it. Thanks for the advice..... .....unfortunately I don't have a core drill. I'm going to need to be able to do this to produce a range of specific sizes - might involve quite a few core drills. Time is the one commodity that I have plenty of - I'll just have to try the other techniques that people have suggested - but thanks for the suggestion anyway.... Regards Adrian Suffolk UK |
#8
|
|||
|
|||
HI Howard
even after repeated attempts and should you be successful, the doughnut (hole) will always be at risk for cracking. Add heat from a soldering iron and for sure a recipe for a crack. Yes - I suppose that's where the core drill solution wins - in that there's no extra stresses induced in the glass. Thanks Adrian Suffolk UK |
#9
|
|||
|
|||
Hi Charles
Thanks for the comments i did this. i took a 3" hole out of the interior of a 16" disk. Same principle, I'm looking at 1" holes from a 3" x 2" rectangle draw out the interior hole with a sharpie = glass cutter ? use a minibit on your grinder to drill a sequence of holes around the perimeter of this line, and a few on the interior of the circle in a small area. score around the perimeter. make lots of scores between the perimeter holes and the interior holes, and across the diameters in a lot of places. CAREFULLY break out the small areas between the interior holes with grozers. work on grozing out the rest of the interior pieces. use the large grinder head to smooth out the perimeter. Sounds like a plan. The problem I was getting was that the circular score was OK, then I made scores across the circle like spokes of a wheel - and they ran OK - but they wouldn't break out because they had 'nowhere to go'. I guess that the ground out holes help with that.... if you do it wrong, you just start over. I've had plenty of practice at that step ! g ps: i heard of someone just scoring the interior cut, and then just punching out the hole with a fist. Sounds like a recipe for a trip to the Emergency ward! Don't think I'll try that g Many thanks Adrian Suffolk UK |
#10
|
|||
|
|||
Hi Dennis
Thanks for the detailed reply. Although it's easier to just drill the hole out, you can cut a circle out from inside a piece of glass. Here's a method I use as a demo in my Cutting Clinics. It's very effective at demonstrating "impossible" cuts. 1. Score the circle you want. Unless you're EXTREMELY good cutting by hand, I'd suggest using a circle cutter. yes - was going to use a circle cutter anyway... 2. Turn the glass over, lay it flat on your table, and tap the circular score until it has cracked completely along the score. I've been running the crack by tapping with the 'blunt end' of the glasscutter - your way sounds more controllable - I'll try it. 3. Turn the glass back to the original side and score an "X" and a "+" to divide the circle into 8 pie-shaped pieces. (BE CAREFUL to NOT run the score past the original score for the circle. Stop those scores about 1/8" short of the circle score. Tried this with 4 sectors - but not been able to get 'the first piece' to come out - I'm sure that, once one piece is out then the rest will follow without too much drama 4. Turn the glass over, again lay it flat on the table, and tap those scores until they have all completely cracked. 5. Stand the glass up vertical and tap the center where the scores intersect. The pie-shaped pieces will fall out leaving a hole in the glass. Presumably to the accompanyment of a drum-roll g - certainly sounds like Magic! - I'll gve it a try. You can also use this same method to cut out extremely complex shapes other than circles. I think I'll stick to circles for the time being - but what kind of shapes were you thinking of ...? Many thanks Adrian Suffolk UK |
|
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
AD: ongoing glass classes - Craft Students League NYC | Craft Students League | Glass | 0 | February 26th 04 08:54 PM |
For those who want to know.. Making Beach Glass With Your Tumbler! | Harry | Beads | 7 | December 22nd 03 08:19 PM |
Glass cutting lubricant | Charles A. Peavey | Glass | 22 | November 7th 03 07:55 PM |
cutting glass into thin sections | jad_23 | Glass | 8 | August 9th 03 03:51 PM |
Old glass receipts | Matthew Spong | Glass | 0 | July 4th 03 01:06 PM |