![]() |
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
![]()
Hello,
I purchased an older electric rolling mill. Brand unknown, no instructions, etc. I need to know are the basic operating instructions for a mill the same as others ? Where can I get instructions in using a mill ? ( a link to a website would be great ) also where can I get Ideas in creating different textures ( how to ) Thanks, Mtnrabbit |
Ads |
#2
|
|||
|
|||
![]()
mtnrabbit wrote:
Hello, I purchased an older electric rolling mill. Brand unknown, no instructions, etc. I need to know are the basic operating instructions for a mill the same as others ? Where can I get instructions in using a mill ? ( a link to a website would be great ) also where can I get Ideas in creating different textures ( how to ) Thanks, Mtnrabbit Hey, lucky old you!!, you must be a hell of a guy to just picked one up? They generally weigh more than most people can lift. Now the older smiths here can help you, but we need to 1. See an image of it 2.Have some dimensions as follows, roll width, roll dia. wether all flat or part grooved. Motor Horse power and rpm Approx roll rpm when running. also overall weight height etc. Finally where are you? As there might just be another working s/gold smith near you who might be willing to help. Did you also look around to see if there was anyonther tools of our trade where you found it? Leave no stone unturned in this sort of situation. |
#3
|
|||
|
|||
![]()
Hello,
Thank you for getting back to me. I had three healthy young men carry the mill into the shop. ( I was lucky ) 1. we need to See an image of it .... ( I can email photos, what is your email address ? ) 2.Have some dimensions as follows, roll width, roll dia. wether all flat or part grooved. .... ( roll width is about 4 in , half flat and half grooved, motor size is 1/2 hp Dayton split gear, 700 lbs torque , Ratio - 42.8:1 Motor Horse power and rpm Approx roll rpm when running. ... ( ? ) also overall weight height etc. ... ( weight heavy, approx 15 in high and 8 wide ) Finally where are you? ... ( In the So California area , Phelan Ca ) Did you also look around to see if there was anyonther tools of our trade where you found it? ... ( the person that owned it died ) Thanks for your help, Dennis PS: I have 90 plus Invitations to Gmail so If anybody in the group wants one please email |
#4
|
|||
|
|||
![]()
mtnrabbit wrote:
Hello, Thank you for getting back to me. I had three healthy young men carry the mill into the shop. ( I was lucky ) 1. we need to See an image of it .... ( I can email photos, what is your email address ? ) 2.Have some dimensions as follows, roll width, roll dia. wether all flat or part grooved. .... ( roll width is about 4 in , half flat and half grooved, motor size is 1/2 hp Dayton split gear, 700 lbs torque , Ratio - 42.8:1 Motor Horse power and rpm Approx roll rpm when running. ... ( ? ) also overall weight height etc. ... ( weight heavy, approx 15 in high and 8 wide ) Finally where are you? ... ( In the So California area , Phelan Ca ) Did you also look around to see if there was anyonther tools of our trade where you found it? ... ( the person that owned it died ) Thanks for your help, Dennis PS: I have 90 plus Invitations to Gmail so If anybody in the group wants one please email By definition your mill is a small silver/gold smiths production one being motor driven, ie designed for continious use as opposed to a hand driven one. there are advantages to both. the hand one can go backwards and forwards quickly to do a no of differnet rolloing operations. Say, reducing a rod to a taper in several stages as opposed to hand forging this down. You cant do this on a powered mill. Tho its a pain rolling out say 20 yards of wire buy hand. thats when the power drive comes into its own. the best otion is to have both hand and power mills. Id like to see an image, ,my email address is ted dot frater at virgin dot net. It could be a Durston, made here in the UK roll proportions are pretty general , ie 4in width will be approx 2.5in dia. Regrettably im in rainy old UK. |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
[ADVERT-FA] Rolling Mill "Smooth" Rollers: Old & Solid | Randylands | Jewelry | 0 | April 30th 04 06:46 AM |
Slitting machine, Slitting, Rolling mill, Wire Flattening Mill, Sheet Leveler, Section Leveler, Scalping Machine, Brush Machine, coiler, decoiler, recoiler, 4 Hi, 6 Hi, 4 High, 6 High, Rolling mill, Wire Flattening Mill, Polishing Machine, Rewinding | korak | Marketplace | 0 | December 14th 03 05:52 PM |
Slitting machine, Slitting, Rolling mill, Wire Flattening Mill, Sheet Leveler, Section Leveler, Scalping Machine, Brush Machine, coiler, decoiler, recoiler, 4 Hi, 6 Hi, 4 High, 6 High, Rolling mill, Wire Flattening Mill, Polishing Machine, Rewinding | korak | Quilting | 0 | December 14th 03 05:52 PM |
Rolling mill success! | HoyoD | Jewelry | 3 | November 9th 03 04:50 AM |