If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
kiln
i have got a big kiln and want to know if i have to use cones for glass
slumping? we are new at this and need to find the temp,s to. Thanks Gail |
Ads |
#2
|
|||
|
|||
|
#3
|
|||
|
|||
On Wed, 11 May 2005 20:54:55 -0600, nJb wrote:
wrote: i have got a big kiln and want to know if i have to use cones for glass slumping? we are new at this and need to find the temp,s to. Thanks Gail You won't be using the cones any more. Go to www.warmglass.com and read the tutorial. While that's good advice, it's not as though it's not possible to use cones, especially for something (relatively) simple like slumping a single layer of glass. I've successfully slumped by putting an 018 cone in the kilnsitter, turning the power on high, and walking away. There's enough thermal mass in the kiln, and the glass is thin enough, that it seems to cool down slowly enough to anneal reasonably well. On the other hand, I only did the one project before I built a digital controller for the beast (setpoint only, for the moment, but for now that's enough.) -- #macro R(L P)sphere{L F}cylinder{L P F}#end#macro P(V)merge{R(z+a z)R(-z a-z)R(a -z-z-z a+z)torus{1F clipped_by{plane{a 0}}}translate V}#end#macro Z(a F T)merge{ P(z+a)P(z-a)R(-z-z-x a)pigment{rgbt 1}hollow interior{media{emission T}}finish{ reflection.1}}#end Z(-x-x.2y)Z(-x-x.4x)camera{location z*-10rotate x*90} |
#4
|
|||
|
|||
Ron Parker wrote:
On Wed, 11 May 2005 20:54:55 -0600, nJb wrote: wrote: i have got a big kiln and want to know if i have to use cones for glass slumping? we are new at this and need to find the temp,s to. Thanks Gail You won't be using the cones any more. Go to www.warmglass.com and read the tutorial. While that's good advice, it's not as though it's not possible to use cones, especially for something (relatively) simple like slumping a single layer of glass. I've successfully slumped by putting an 018 cone in the kilnsitter, turning the power on high, and walking away. There's enough thermal mass in the kiln, and the glass is thin enough, that it seems to cool down slowly enough to anneal reasonably well. On the other hand, I only did the one project before I built a digital controller for the beast (setpoint only, for the moment, but for now that's enough.) I second what these guys said; you *can* use cones but you probably won't want to. An analog pyrometer and infinite control switch are inexpensive and can be effectively used to manually control your temperatures, but you'll be much happier with a digital controller, which you can build yourself as Ron did or purchase from a supplier such as www.cdvkiln.com. A basic fusing book like "Contemporary Warm Glass" by Brad Walker is another great place to start. Good luck! -- -Kalera http://www.beadwife.com |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
electric kiln firing questions | Zander | Pottery | 5 | October 11th 04 02:31 AM |
Important - Please beware of a company called Bohle | Eric Russell | Glass | 2 | August 23rd 04 07:46 PM |
FAQ Raku part 2 of 2 | SBRANFPOTS | Pottery | 0 | October 21st 03 02:13 PM |
FAQ Raku part 2 of 2 | SBRANFPOTS | Pottery | 0 | September 16th 03 11:11 PM |
Raku FAQs | Tom Buck | Pottery | 0 | July 20th 03 04:49 AM |