If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Carving Texture & Fur
Hi-
I'm trying to ifnd out how to make decent fur on a carving. All the books I've read, just mumble something about adding texture and get past the subject in under 25 words. Some books have a lot to say about burning feathers into a woodcarving. I am not real interested in wood burning. I haven't painted the things I've carved. Thata means I would like to be able to texture a carving using chisels or equivalent. Can someone offer some suggestions or possibly a good book that describes how to create texture, fur, hair, etc without using a woodburner? Thanks in advance - Jim 11.22.2003 |
Ads |
#2
|
|||
|
|||
Jim
If your using wood and dont onject to using a motorized tool with your project. I use a squared off diamond bit in a dremel too for feather lines. Or you can use the tool to make the whole feather if your making a bigger bird. I like to make some feather bumps on the subject then go over it using the diamond stone. Hope this helps. Will -- http://www.geocities.com/hush88ca/Mi..._Carvings.html "Jim" wrote in message ... Hi- I'm trying to ifnd out how to make decent fur on a carving. All the books I've read, just mumble something about adding texture and get past the subject in under 25 words. Some books have a lot to say about burning feathers into a woodcarving. I am not real interested in wood burning. I haven't painted the things I've carved. Thata means I would like to be able to texture a carving using chisels or equivalent. Can someone offer some suggestions or possibly a good book that describes how to create texture, fur, hair, etc without using a woodburner? Thanks in advance - Jim 11.22.2003 |
#3
|
|||
|
|||
One more thing. If you use the diamond stone start from the tail and worl
your way forward. It hides the start of each mark. Good luck Will "Jim" wrote in message ... Hi- I'm trying to ifnd out how to make decent fur on a carving. All the books I've read, just mumble something about adding texture and get past the subject in under 25 words. Some books have a lot to say about burning feathers into a woodcarving. I am not real interested in wood burning. I haven't painted the things I've carved. Thata means I would like to be able to texture a carving using chisels or equivalent. Can someone offer some suggestions or possibly a good book that describes how to create texture, fur, hair, etc without using a woodburner? Thanks in advance - Jim 11.22.2003 |
#4
|
|||
|
|||
You might want to look at some books on pyrography. Although woodburning is
an adjunct used by many carvers, you might find more information in books specific to burning. I made a full round bear carving a couple years ago and burned the fur. It turned out quite good. Think of using the tool as if it were a v-gouge. Short tight strokes where the fur is short, like the muzzle, and longer looser strokes where the fur is shaggy. With a bit of practice I think you'd pick it up quickly. You can get a pencil burner from a craft store inexpensively but it won't give you the range of control that comes with the more expensive models. If you belong to a carve club, you might find someone who will let you try out their unit and probably be glad to give you some pointers. Good luck, JT |
#5
|
|||
|
|||
Kind of depends on the size of the critter you are putting fur on.
I have been using small "U" gouges very successfully. Fur on a long haired animal (ie Bear) is different from that of a mountain lion.. Longer haired animals layer similar to the longer beard on a man.. or hair on our heads.. Hair overlaps hair.. and it doesn't all go in the same direction. You might want to picture how hair/fur works.. by looking at a cat or a dog.. Notice how it comes off the nose.. and kinda follows gravity.. moving back and down from the center.. however, the center doesn't have a part.. it goes in different directions..but generally the same at the center.. and then begins following gravity as it progresses down the side of the animal. So.. a rule of thumb.. use small "U" gouges.. 1, 2, 3 mm #11's. I've been told by a number of professional animal carvers (Debbie Edwards and Kurt Curtis are two of them) to not use "V" gouges.. looks unnatural. Might take a look at the bears in my picturetrail site.. they were done with "U" gouges and highlighted with pyrography.. woodburner. -- Bill Splaine, Healdsburg, CA Woodcarvings: www.picturetrail.com/chips --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.544 / Virus Database: 338 - Release Date: 11/25/2003 |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Carving bases, alabaster and otherwise | Joe Ahearn | Carving | 7 | November 13th 03 01:52 PM |
Basswood carving | bubba | Carving | 1 | October 6th 03 04:35 PM |
Need good source for carving gloves | Bill Houdek | Carving | 3 | September 4th 03 04:21 PM |
carving | Joe Kennedy | Carving | 2 | August 5th 03 06:33 PM |