If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Seeking Kiln Advice
I'm going to upgrade my kiln very soon. The one I have for glass is to
restrictive in space and I want to do some large pieces. I wanted to know if anyone had some good suggestions, experience, etc. for a kiln. I would like it to have at least a 12" height, and at the very least 17" wide. Money is somewhat limited, I can't spend $4,000 for a super duper model, but I can look at pieces under a thousand. I would like to have a kiln controller with the kiln and would like advice and experience as well. Thanks! Starlia |
#2
|
|||
|
|||
I got a kiln at a garage sale for $300. It is a ceramic kiln with no
controller to speak of (off, lo, med & hi). It has a chamber that is about 14" across. Even one of the elements has come loose and is on the floor of the kiln. I have done slumping, fusing and vitreous paint firing with it. I did get an analog pyrometer. My kiln isn't the "best" for glass, but it works and I would probably still be waiting to do fusing if I had to wait to have enough money to get the "best" kiln for glass. Remember, a kiln is just a really hot oven. No more, no less. Since then I have gotten more kilns (about 10 at last count) and only a couple are real honest-to-goodness glass kilns. But the Egyptians and Venetians didn't have kilns as good as mine and their stuff came out okay. Good tools are great, but any tool that works is better than no tool at all. You probably will want to keep your smaller kiln hooked up as an annealer. Otherwise, do what your budget allows. Keep an eye out in the local paper and garage sales. You can get a real deal sometimes. -- There are no mistakes, only unexplored techniques "saucy" wrote in message ... I'm going to upgrade my kiln very soon. The one I have for glass is to restrictive in space and I want to do some large pieces. I wanted to know if anyone had some good suggestions, experience, etc. for a kiln. I would like it to have at least a 12" height, and at the very least 17" wide. Money is somewhat limited, I can't spend $4,000 for a super duper model, but I can look at pieces under a thousand. I would like to have a kiln controller with the kiln and would like advice and experience as well. Thanks! Starlia |
#3
|
|||
|
|||
In article ,
"saucy" wrote: I'm going to upgrade my kiln very soon. The one I have for glass is to restrictive in space and I want to do some large pieces. I wanted to know if anyone had some good suggestions, experience, etc. for a kiln. I would like it to have at least a 12" height, and at the very least 17" wide. Money is somewhat limited, I can't spend $4,000 for a super duper model, but I can look at pieces under a thousand. I would like to have a kiln controller with the kiln and would like advice and experience as well. Thanks! Starlia Evenheat makes very good, very affordable glass kilns. I've had one for... my gosh... over six years, and never a bit of trouble. Bullseye uses Evenheat kilns for their compatibility test firings, or at least, did when I worked there... I consider that a good testament to their durability. You might also try posing your question to the WetCanvas glass forum, http://www.wetcanvas.com. -- -Kalera Mom of Juliet, 5, Sam, 3, and Ophelia, born 5/31/03 Wife of the incomparable Moxley of www.spaceplex.com See us at www.strattonhome.org |
#4
|
|||
|
|||
Try Centre de Verre, link is on the warm glass site at www.warmglass.com.
There is a lot of good kiln info there. I have a Jen Ken kiln I'm very satisfied with which I bought from Marty at CdV, but it's a smaller one. Patti |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Lampworking - need torch advice. | BethF | Beads | 15 | January 23rd 05 07:13 AM |
Kiln question | Kalera Stratton | Beads | 13 | July 11th 03 06:35 AM |
Newbie!!! (i admit it, and need all the advice i can get) | C. Gregory | Beads | 7 | July 9th 03 04:31 AM |
Need some advice | Jalynne | Beads | 11 | July 5th 03 11:20 PM |
Enameling Kiln | Tink | Beads | 6 | July 2nd 03 01:01 PM |