A crafts forum. CraftBanter

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Home » CraftBanter forum » Craft related newsgroups » Jewelry
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

rolling mill questions



 
 
Thread Tools Display Modes
  #1  
Old September 19th 06, 07:38 AM posted to rec.crafts.jewelry
ted frater
external usenet poster
 
Posts: 133
Default rolling mill questions

[[moderator edited, from email apparently intended at least in part (thus the
editing) for the group...]]

Interesting how the use of the word "Pallion" has different uses.
Yes I know the normal use in our trade is to describe little pieces of
solder
BUT here the other meaning is the little pieces of gold or silver that
are used under clear enamel on watch faces and jewellery as decoraton.
these are about 1/10th mm thick and are stamped in relief in red ,yellow
and green gold as well as fine silver.
Bayeler has supplied me in the past with all sorts of designs , last
time in 1978. but particularly the zodiac 12 and others like the French
fleur de lys. Lovely to use too.

Ive 2 catalogues of theirs witlh pictures of all the designs they make
and the no run to over 1500.

their address and Ph no is
Bayeler & Cie .S.A.
Fabrique de Cadrans
2-4 rue des deux-ponts 1211 Geneva 8
Switzerland

Tel. 0041 022 24 62 40
Just on the off chance you know of an agent in the usa.

youd enjoy using them.
So simple to use. once youve enamelled the work piece you just stick
the paillion ontop of the enamel with a tiny bit of spittle, Yes!!
its fine,
using a tiny paint brush to pick it up and place it.
then re fire it and it settles onto the enamel all by itself. no
oxidation . then you put a tiny dusting of cleat or clear coloured
enamel on top , re fire asnd its done.
looks great.
Ted







 




Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Rolling Mill Kendall Davies Jewelry 13 July 17th 12 06:07 PM
rolling mill questions br Jewelry 30 September 23rd 06 09:45 PM
I just picked up a ROLLING MILL , now I have some questions ! mtnrabbit Jewelry 3 November 9th 05 10:02 AM
Slitting machine, Slitting, Rolling mill, Wire Flattening Mill, Sheet Leveler, Section Leveler, Scalping Machine, Brush Machine, coiler, decoiler, recoiler, 4 Hi, 6 Hi, 4 High, 6 High, Rolling mill, Wire Flattening Mill, Polishing Machine, Rewinding korak Marketplace 0 December 14th 03 06:52 PM
Slitting machine, Slitting, Rolling mill, Wire Flattening Mill, Sheet Leveler, Section Leveler, Scalping Machine, Brush Machine, coiler, decoiler, recoiler, 4 Hi, 6 Hi, 4 High, 6 High, Rolling mill, Wire Flattening Mill, Polishing Machine, Rewinding korak Quilting 0 December 14th 03 06:52 PM


All times are GMT +1. The time now is 09:22 AM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 CraftBanter.
The comments are property of their posters.