If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Lampwork Repair Question
I have a vessel shaped like this one... http://snipurl.com/7fj2. While
the one in the link example has gorgeous flowers, the inside of the bead hole is really yucky looking. And it looks the same as one I have that I'd like to fix - except mine is still chipped and hasn't been sanded down yet. I was thinking of using a jeweler's file to sand down the obvious chips on my vessel, but then I expect it would look like the one in the link I give... all frosted and sanded-looking. Is there anything I can put on the bead hole that will make it shiny again? I was considering putting a Swaro crystal on a piece of SS wire to fit it tightly inside the hole, then gluing the whole thing into the hole using Jeweler's Glue. But the sanded edges would probably still show around the crystal base. Would fingernail polish work to put a shine back on the bead hole? Or do you think should I just frost the whole vessel after sanding the chipped hole? Thanks! Linda --- -- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.712 / Virus Database: 468 - Release Date: 6/27/2004 |
Ads |
#2
|
|||
|
|||
On Wed, 30 Jun 2004 12:56:33 GMT, "bluemaxx"
wrote: Would fingernail polish work to put a shine back on the bead hole? Or do you think should I just frost the whole vessel after sanding the chipped hole? Flame polishing would probably be overkill, so I'd suggest something like Future floor polish. I would guess clear fingernail polish would work, as well. |
#3
|
|||
|
|||
A jeweler's file or bead reamer will work to sand down the hole, and yes,
fingernail polish will be fine to make the glass shiny again. Some people actually do this with transparent glass beads because the polish makes the hole almost disappear. You have the right idea! -- Kandice Seeber Air & Earth Designs http://www.lampwork.net I have a vessel shaped like this one... http://snipurl.com/7fj2. While the one in the link example has gorgeous flowers, the inside of the bead hole is really yucky looking. And it looks the same as one I have that I'd like to fix - except mine is still chipped and hasn't been sanded down yet. I was thinking of using a jeweler's file to sand down the obvious chips on my vessel, but then I expect it would look like the one in the link I give... all frosted and sanded-looking. Is there anything I can put on the bead hole that will make it shiny again? I was considering putting a Swaro crystal on a piece of SS wire to fit it tightly inside the hole, then gluing the whole thing into the hole using Jeweler's Glue. But the sanded edges would probably still show around the crystal base. Would fingernail polish work to put a shine back on the bead hole? Or do you think should I just frost the whole vessel after sanding the chipped hole? Thanks! Linda --- -- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.712 / Virus Database: 468 - Release Date: 6/27/2004 |
#4
|
|||
|
|||
Thanks, Tink and Kandice. )))
I knew you guys would come up with good answers... although I have no idea what 'flame polishing' is, Tink... or how I could do it. Maybe hold my Zippo lighter to it long enuff to melt the edges?? lol Linda --- -- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.712 / Virus Database: 468 - Release Date: 6/27/2004 |
#5
|
|||
|
|||
Is there anything I can put on the bead hole that will make it shiny again? I was considering putting a Swaro crystal on a piece of SS wire use a very fine diamond file and polish off the rough spots etc. if you want it "clear" looking when done - either you would have to use a rotary tool with cerium oxide -and rouge powder to polish - yes you can polish glass to shiny - but it takes a long time. Quick and "cheat" way - would be to coat the inside with "FUTURE" clear floor polish - this takes away the "matte" look and makes bead holes look "clearer" - (tip I heard from a famous lampworker long time ago - -) Cheryl DRAGON BEADS Flameworked beads and glass http://www.dragonbeads.com/ |
#6
|
|||
|
|||
or how I could do it. Maybe
hold my Zippo lighter to it long enuff to melt the edges?? lol NO _ don't EVEN try it (in jest) it will crack the vessel. If you know someone with lapidary equipment - they can polish the top in a matter of minutes.. Cheryl DRAGON BEADS Flameworked beads and glass http://www.dragonbeads.com/ |
#7
|
|||
|
|||
Very cool tips, Cheryl. I'll try the future floor polish also!
I have a few matte beads that have a few spots on them that didn't take the etching solution as well as the rest of the bead. Sounds like dipping them in Future might be able to fix that problem, also! Thanks! Linda "Cheryl" wrote in message ... : : if you want it "clear" looking when done - either you would have to use a : rotary tool with cerium oxide -and rouge powder to polish - yes you can polish : glass to shiny - but it takes a long time. : Quick and "cheat" way - would be to coat the inside with "FUTURE" clear floor : polish - this takes away the "matte" look : and makes bead holes look "clearer" - : (tip I heard from a famous lampworker long time ago - -) : Cheryl : DRAGON BEADS : Flameworked beads and glass : http://www.dragonbeads.com/ : --- -- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.713 / Virus Database: 469 - Release Date: 6/30/2004 |
#8
|
|||
|
|||
I'll try the future floor polish also!
I have a few matte beads that have a few spots on them that didn't take the etching solution as well as the rest of the bead. Sounds like dipping them in Future might be able to fix that problem, also! Thanks! Linda I don't think it will totally make a matte bead shiny again..... AND it will wear off with time. If you have some matte beads that are not evenly matte --- why not just buy a jar of dip n etch -- and redip the rascals??? Cheryl Cheryl DRAGON BEADS Flameworked beads and glass http://www.dragonbeads.com/ |
#9
|
|||
|
|||
|
#10
|
|||
|
|||
Bullseye seems slightly resistant to etching, while Japanese glass
etches if you accidentally sneeze too close to it. Both do etch so nicely with a sandblaster or a rock tumbler, though! -Kalera http://www.beadwife.com http://www.snipurl.com/kebay Tinkster wrote: On 01 Jul 2004 15:44:10 GMT, eads (Cheryl) wrote: If you have some matte beads that are not evenly matte --- why not just buy a jar of dip n etch -- and redip the rascals??? I've had the same problem with etching beads sometimes: They don't always etch evenly. I thought it was my etching solution, so I bought a new bottle. Same issue. I've not examined the situation enough to say if it's a particular kind or color of glass yet. That's one of the reasons I decided to get a sandblaster. LOL! Tink |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Lampwork Question | Black Cat Beads | Beads | 5 | February 24th 04 10:46 PM |
Question on lampwork beads | Cheryl | Beads | 18 | February 19th 04 05:07 AM |
Lampwork set question | Christina Peterson | Beads | 39 | November 7th 03 04:45 AM |
Lampwork bead repair? | bluemaxx | Beads | 0 | October 15th 03 03:38 AM |
Lampwork question | CLP | Beads | 24 | August 24th 03 03:08 AM |