If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Hanging latch hook
OK, I stitched the binding on the Snoopy latch hook and left a casing at
the top so we can hang it. I went to look at dowels and finials and could only find knobs that fit on the skimpy, thin (3/16" I think) dowels which won't be strong enough to hold a 20"W x 30"L latch hook piece. I believe a 3/8" dowel will fit in the casing since the rubber grip on my ink pen will fit in there and that is what It measures. Might be able to go slightly thicker since the rubber didn't want to slide through the casing whereas a smooth dowel will. Any ideas where I can find something to put on the ends of a 3/8" dowel and what kind of wire/cord should be used to hang it? -- Brenda Tickler of Chuzzles |
Ads |
#2
|
|||
|
|||
Hanging latch hook
Brenda Lewis wrote:
OK, I stitched the binding on the Snoopy latch hook and left a casing at the top so we can hang it. I went to look at dowels and finials and could only find knobs that fit on the skimpy, thin (3/16" I think) dowels which won't be strong enough to hold a 20"W x 30"L latch hook piece. I believe a 3/8" dowel will fit in the casing since the rubber grip on my ink pen will fit in there and that is what It measures. Might be able to go slightly thicker since the rubber didn't want to slide through the casing whereas a smooth dowel will. Any ideas where I can find something to put on the ends of a 3/8" dowel and what kind of wire/cord should be used to hang it? I'd check a window treatments store. Elizabeth -- *~*~*~*~*~*~*~*~*~*~living well is the best revenge~*~*~*~*~*~*~*~*~* The most important thing one woman can do for another is to illuminate and expand her sense of actual possibilities. --Adrienne Rich *~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~*~ *~*~*~*~*~*~*~*~*~* |
#3
|
|||
|
|||
Hanging latch hook
I used knobs, normally used on drawers and cupboards. There's a big variety
available. Joyce in RSA. "Brenda Lewis" wrote in message .. . OK, I stitched the binding on the Snoopy latch hook and left a casing at the top so we can hang it. I went to look at dowels and finials and could only find knobs that fit on the skimpy, thin (3/16" I think) dowels which won't be strong enough to hold a 20"W x 30"L latch hook piece. I believe a 3/8" dowel will fit in the casing since the rubber grip on my ink pen will fit in there and that is what It measures. Might be able to go slightly thicker since the rubber didn't want to slide through the casing whereas a smooth dowel will. Any ideas where I can find something to put on the ends of a 3/8" dowel and what kind of wire/cord should be used to hang it? -- Brenda Tickler of Chuzzles |
#4
|
|||
|
|||
Hanging latch hook
Did you just glue them on?
Joyce wrote: I used knobs, normally used on drawers and cupboards. There's a big variety available. -- Brenda Tickler of Chuzzles |
#5
|
|||
|
|||
Hanging latch hook
DH made a hole in the shank of the knob, before gluing the dowel in. My
dowel is thicker than yours, so he had to reduce that too. The result was admired by other stitchers who saw it, as well as the hardanger hanging which it held. Joyce in RSA. "Brenda Lewis" wrote in message Did you just glue them on? |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Latch Hook question | Diane | Needlework | 3 | August 9th 04 11:10 AM |
Latch Hook Rug Design Software - Rugware | Latch Hook Design Software | Marketplace | 0 | December 2nd 03 12:37 PM |
OT latch hook? | Puffins | Quilting | 3 | August 27th 03 03:08 AM |
site about latch hook charts | Stella Fenley | Yarn | 0 | August 21st 03 04:08 PM |
Help with finding pre printed latch hook canvas | Sonya Cirillo | Yarn | 1 | August 14th 03 02:22 PM |